Хайлт

Цуцлах
Minelab

EQUINOX 600 / 800 Software Update 3.0

Шинэ юу байна?

Одоо байгаа 5, 10, 15, 20, 40 кГц хувилбаруудад 4 кГц давтамжтай шинэ давтамж нэмэгдэв. Энэхүү шинэ 4 кГц давтамж нь томоохон гүнзгий зорилтот түвшинг, ялангуяа Азийн зарим хэсэгт илрүүлдэг. Эдгээр нөхцлийг оновчтой болгосны үр дүнд энэхүү шинэ давтамж нь бусад нэг давтамжтай харьцуулахад хэрэглэгчид өөр өөр хариу үйлдэл үзүүлэх болно.

Бусад бүх дан болон олон давтамжийн тохиргоо нь гүйцэтгэлдээ өөрчлөгддөггүй.

4 кГц-ийн сайжруулалтын функцээс гадна янз бүрийн тогтвортой байдлын сайжруулалтыг оруулсан болно.

For step-by-step instructions on downloading the software, please refer to the following brochures:

Download the EQUINOX 600 / 800 Software Upgrade 3.0 Instructions (EN)

Download the EQUINOX 600 / 800 Software Upgrade 3.0 Instructions (ZH)

Minelab Update Utility (MUU) Details

Minimum System Requirements:

USB 2.0 port
EQUINOX USB Charging Cable with Magnetic Connector

Windows 10

50 MB of hard drive space
20 MB of RAM

MAC OS

Greater than 10.13 High Sierra
50 MB of hard drive space
30 MB of RAM

Note:

  • Only one EQUINOX 600 / 800 can be connected to your computer during the update operation.
  • The EQUINOX 600 / 800 must be ON during the software update.
  • Any custom detector settings will be preserved while performing the update.
  • An internet connection is required to download the Minelab Update Utility to the computer, however, an internet connection is not required to update the EQUINOX 600 / 800 and this can be done offline.
  • The EQUINOX coil must be connected to perform the update.

Important: Do not turn off or disconnect the EQUINOX 600 / 800 during the update process.

Once the MUU is downloaded, open the application and follow these instructions:

1. Connect the EQUINOX 600 / 800 to the computer USB port using the magnetic charging cable and turn on the detector.

2. When the EQUINOX 600 / 800 is identified, the MUU will communicate with the detector and determine the current software version.  

3. If an update is available, the MUU will display Updates are available for your detector. Click INSTALL to begin the upgrade or QUIT to close the MUU.

4. If the metal detector is up to date, the application will display Your detector is up to date and prompt you to QUIT the application.

5. The EQUINOX 600 / 800 screen will go blank during the update; a green LED on the top left corner of the control box will blink rapidly while the update is in progress.

6. Installation will take approximately 1 minute.

Once the upgrade is complete, the EQUINOX 600 / 800 will restart and the MUU will prompt you to disconnect the detector and QUIT the application.

Note: Close the application and reopen if updating multiple EQUINOX 600 / 800 detectors 

 

Дээшээ буцах

arrow_back Minelab
arrow_back Main Menu
arrow_back Minelab
arrow_back Бүтээгдэхүүний шүүлтүүрүүд
arrow_back Minelab
arrow_back Filters